Using LCP panels to localize lighting controls offers several distinct advantages:

• The cost to design, layout, construct, wire, and program a lighting system is greatly reduced.
• The transmission / receiving characteristics of a central-star system are vastly superior than a conventionally wired system.
• The LCP panels are designed to properly dissipate the heat generated by PCS lighting controls.
• The finished product using LCP lighting panels results in a professional, rugged, high-quality system

The new SceneMaster lighting control system allows the designer/installer to implement up to sixteen pre-set scenes, (user pre-set lighting levels) for each circuit. The SceneMaster lighting system allows for four scenes per room (such as the dining room, living room, home theater, and bedrooms), four pathway scenes (such as lighting the path between your bedroom and the kitchen), and eight whole-house scenes (such as Night, Away, Home and Alarm).

All PCS products are made in the USA and carry a five-year limited warranty.

Features

• Construction
  The LCP series enclosure is a rugged NEMA1 grade panel made of 16 gage steel with a powder coat finish.
• Mounting
  The LCP is designed to be flush-mounted between two 16 inch center to center studs or surface-mounted on any flat surface. A matching one inch bezel is provided for finishing a flush mount installation.
• Simple Wiring
  Enclosure is provided with 13 knockouts (1/2x3/4 combo type) on both the top and the bottom of the unit and 20 on the rear.
• Security
  A locking door with two keys is provided to insure against tampering or reprogramming by unauthorized persons. Keys are common to all LCPs for easy replacement.
• Documentation Storage
  A special slot is provided in the inside of the door to hold the SceneMaster Programming guide and programming worksheets.
• Hinged/Removable Interior Panel
  The interior LM4 mounting panel is designed with removable hinges so it may be completely removed from the enclosure so that LM4s, switches, receptacles or transmitters may be easily installed and wired. While installed the mounting panel can swing 90 degrees out of the enclosure for wiring the rear of the LM4s or other equipment.
• Relay Control
  The LCP panel interior is provided with inserts for mounting up to four 240VAC 20A 2 Pole heavy duty relays for control of motors, pumps, gates, etc. These relays can be driven from any output of an LM4.
• Utility Bay
  On the lower section of the interior panel there is a standard four gang bay provided for the installation of receptacles, slave switches, or transmitters. A receptacle is useful for connecting testers or programming devices. One or more slave switches can be used to provide emergency control of LM4 circuits as a backup to X-10 or other system controls.

Ordering Information

• Part Number
• LCP16-8000 (8000W, 16 Circuits)
• LCP16-0 (Enclosure only)

Installation

• Pre-wire
  Wire one 12ga 20A feed from main panel to LCP location for each LM4 to be installed. Wire one 12ga circuit for each load circuit or control point back to LCP location.

Additional Information

• Load Types
• Dimming (Lamp) Outputs
• Incandescent or
• Magnetic Low Voltage.
• Rating
• NEMA1 (indoor only)
• Warranty
• Two year limited warranty.

Specifications

Model Number LCP16-8000 Circuits 16 Channels / Dimming (Triac) Base Module LM4L/S-2000 x 4 Total Load 8000 W / 8000 VA Max Load / Circuit 1000 W Min Dimmer Load 60 W Inductive / Low Voltage Yes Remote Switch Control Yes Bezel Provided Yes Utility Bay 4 gang Components Installed 2 Receptacle / 2 SSR Remote Switch Connections Terminal Block 12 gauge Knockouts Top/Bottom/Rear 13/13/20 ½ x ¾ combo type Dimensions (inches) 28.5H x 14W x 5.0D Weight 25 lbs. Mounting Flush or Surface Operating Temperature -40 F to 104 F